Server Rack Sizes: Understanding the Differences
Server rack sizes are described by three measurements: height in rack units, width and depth. Height and width follow a published standard. Depth does not, so it deserves the most attention before you order.
This guide to server rack sizes explains each measurement in inches and millimeters, shows how the outside of a cabinet differs from the space inside it, and ends with a short method for picking a size that fits both your equipment and your building.
Quick Answer
The standard server rack size is a 19 inch rack that is 42U tall. A 42U cabinet has 73.5 inches of mounting height, stands about 79 to 81 inches tall on the outside, is 600 mm (23.6 in) or 800 mm (31.5 in) wide, and is 800 to 1,200 mm (31.5 to 47.2 in) deep. Equipment width is fixed at 19 inches by the EIA-310 standard. Other common server rack sizes are 24U and 48U.
The Three Server Rack Dimensions
Server rack sizes on a spec sheet list height, width and depth, but each one is measured differently. Height is counted in rack units. Width is quoted twice, once for the equipment and once for the cabinet. Depth is quoted as an outside figure that is always larger than the usable space.

Keeping those differences straight is most of what there is to know about server rack dimensions. The sections below take them one at a time.
Server Rack Height: Rack Units Explained
One rack unit, written 1U, is 1.75 inches (44.45 mm). Server rack height is the number of units multiplied by 1.75, so a 42U rack has 73.5 inches of mounting space.
That figure is the space between the rails. The cabinet itself is taller, because the frame, top panel and casters or leveling feet add several inches. The table shows common server rack sizes with both numbers, plus a check that buyers often miss: whether the cabinet will pass through a standard 80 inch US interior door standing upright.
| Rack size | Mounting height | Typical outside height | Clears an 80 inch door upright? | Typical use |
|---|---|---|---|---|
| 18U | 31.5 in | 35 to 39 in | Yes | Branch office, AV, small network |
| 24U | 42 in | 47 to 50 in | Yes | Half rack for a small server room |
| 42U | 73.5 in | 79 to 81 in | Tight, check the spec sheet | Standard for server rooms and data centers |
| 45U | 78.75 in | 84 to 86 in | No | Rows that need a few more units |
| 48U | 84 in | 89 to 91 in | No | High density rooms with tall ceilings |
Outside heights vary by manufacturer, so treat that column as a range and confirm it on the product page.
A fully assembled cabinet usually arrives strapped to a pallet, which adds another five or six inches. A 42U cabinet that would clear the door on its casters will not clear it on the pallet, so plan where it comes off.
Server Rack Width: 19 Inches Inside, 600 or 800 mm Outside
Server rack width means two things. The equipment width is 19 inches (482.6 mm), measured across the front panel of a device including its mounting ears. EIA-310 also fixes the clear opening between the rails at 17.75 inches (450.85 mm), which is why a server from one manufacturer fits a rack from another.

For most server rack sizes, the outside width of the cabinet comes in two options:
- 600 mm (23.6 in) is the common width for server cabinets. It matches a 24 inch raised floor tile, so rows line up with the floor grid.
- 800 mm (31.5 in) adds about four inches on each side of the rails for vertical cable managers. It suits network cabinets and any rack with a high port count.
Two other standards exist. Telecom racks can be 23 inches wide, and Open Rack hardware uses a 21 inch equipment bay. Neither accepts 19 inch equipment without adapters, so check before buying used hardware.
Server Rack Depth: The Measurement Without a Standard
Server rack depth is set by the manufacturer. Across server rack sizes from 18U to 48U, common outside depths are 600, 800, 1,000 and 1,200 mm (23.6, 31.5, 39.4 and 47.2 in).
The number that matters is usable depth, which is the distance from the front rail to the rear rail. It is always less than the outside depth, because doors and the frame take up space, and on most cabinets it is adjustable. RaxGrid cabinets, for example, have rails that slide front to back so the same frame can hold shallow network gear or deep servers.
A workable rule is the depth of your deepest device plus 3 to 6 inches for cables, power strips and airflow.
- Switches and patch panels are often 12 to 18 inches deep. A 600 or 800 mm cabinet is enough.
- Most 1U and 2U enterprise servers are 28 to 32 inches deep. They need a cabinet at least 1,000 mm deep, and 1,200 mm once rear PDUs and cable management arms are fitted.
When the server rack depth is too small, the rear door will not close. When it is far too large, floor space is wasted in every row.
How Cabinet Type Changes the Footprint
Server cabinet sizes are quoted for the outside of an enclosed cabinet with its doors and side panels. An open frame rack with the same rail dimensions has a smaller footprint, because it has no panels, and it is easier to get through a doorway. An enclosed cabinet takes more floor but gives you locking doors and controlled airflow.

Whichever server rack sizes you compare, the working space around the rack is part of the footprint. TIA-942 calls for at least 3 feet of clearance at the front and 2 feet at the rear, and 3 feet at the rear is easier to work in. Add those to the cabinet depth before you compare server cabinet sizes against a floor plan.
A Five Step Server Rack Size Guide
Use this short server rack size guide before you request a quote.
1. Add Up the Rack Units
List every device and its height in U, including PDUs, cable managers and blanking panels. Add 20 to 30 percent for growth and round up to the next of the standard server rack sizes.
2. Measure the Deepest Device
Take the depth from the manufacturer's spec sheet, add 3 to 6 inches, and compare the result with the cabinet's usable depth.
3. Choose the Width by Cable Count
Pick 600 mm for server heavy racks and 800 mm where patch panels and switches fill most of the rack.
4. Check the Room
Measure ceiling height. NFPA 13 requires 18 inches of clear space below sprinkler heads, which rules out the tallest server rack sizes in many rooms. Then check the floor. A cabinet loaded to 2,000 lb on a 600 by 1,000 mm footprint puts roughly 300 pounds on each square foot, and typical US office floors are designed for a live load of 50 pounds per square foot. Outside a purpose built server room, ask a structural engineer.
5. Check the Route
Walk the path from the loading dock to the room with a tape measure. Note door heights, elevator capacity and tight corners. Older commercial buildings, which are common across New England where RaxGrid is based, may have low doorways and small freight elevators, and both limit which server rack sizes can reach the room.
RaxGrid supplies 42U server and network cabinets in 600 and 800 mm widths and 600, 800 and 1,000 mm depths, delivered fully assembled to sites across the United States. Our team is based in Salem, New Hampshire. If you are unsure which of these server rack sizes fits, send us your equipment list and room measurements.
Frequently Asked Questions
What are the most common server rack sizes?
The most common server rack sizes are 42U for full height cabinets and 24U for half racks. Both use 19 inch mounting rails and come in 600 or 800 mm widths.
What are the standard rack dimensions for a data center?
The usual standard rack dimensions are 42U high, 600 mm (23.6 in) wide and 1,000 to 1,200 mm (39.4 to 47.2 in) deep, with 19 inch mounting rails. Some facilities use 45U or 48U cabinets and 800 mm widths for network rows.
How tall is a 42U rack?
A 42U rack has 73.5 inches (1,867 mm) of mounting height. The cabinet itself is usually 79 to 81 inches tall, depending on the frame and whether it sits on casters or leveling feet.
How deep should a server rack be?
Deep enough for your longest device plus 3 to 6 inches. For current rack servers that usually means a 1,000 or 1,200 mm cabinet. For network equipment, 600 or 800 mm is normally enough.
Are all server racks 19 inches wide?
Nearly all IT racks use 19 inch mounting. The outside of the cabinet is wider, typically 600 or 800 mm. Telecom racks at 23 inches and Open Rack at 21 inches are the main exceptions.
How many servers fit in a 42U rack?
In theory, 42 servers that are 1U each. In practice the count is lower, because switches, PDUs and cable managers take rack units, and the room's power and cooling usually run out before the space does.
Do server rack sizes differ between brands?
Height and equipment width do not, because both follow EIA-310. Outside dimensions and usable depth do differ, so compare standard rack dimensions on the spec sheet instead of relying on the U count alone.
Share
